Newsmy has launched the K99, a 200W 2C1A smart digital display car charger. This car charger supports DC 12-24V wide voltage input and is compatible with the cigarette lighter interfaces of both passenger cars and large trucks.
The product features two USB-C ports and one USB-A port on the output side, supporting simultaneous output from all three ports to meet the fast charging needs of laptops, tablets, and smartphones.
In addition, this car charger integrates a color smart digital display screen into the output panel. When powered on, it displays the total output power in real-time, as well as the power, voltage, and current parameters for each of the three ports, allowing users to intuitively monitor device charging status.
To date, Charging Head Network has published over 175 car charger teardown reports.
Below, Charging Head Network presents a detailed teardown of this product to examine its internal design and components.
Product Appearance
The packaging box features a red and white contrasting color design, with the Newsmy brand logo, slogan, and product name printed in the top left corner.
The back of the packaging box contains product precautions, operating instructions, manufacturer information, etc.
This Newsmy car charger adopts a black plastic housing with a fine-grain matte finish on the main body surface, which resists fingerprints. The unit features a tapered design (narrower at the bottom, wider at the top), with vertical stripes on the transition area and a blue glossy decorative ring around the top edge.
Side view of the unit shows symmetrical silver metal negative spring clips on both sides of the input end, used to secure the body and connect to the negative terminal of the cigarette lighter.
The product specification nameplate is laser-engraved on the rear housing.
Detailed specifications on the rear nameplate are as follows:
Model: K99
Input: DC 12-24V
Output:
USB-C1: 5V-20V 2A-6A or PD 20V 3.25A (120W Max)
USB-C2: 5V 3A, 9V 3A, 12V 3A, 15V 3A, 20V 2.25A
USB-A: 5V 3A, 9V 3A, 11V 6A, 12V 3A (66W Max)
The top surface of the car charger features a black glossy translucent panel surrounded by a blue decorative border. The panel houses three output ports: USB-C2, USB-A, and USB-C1. A hidden color digital display screen is integrated into the lower half of the panel.
Close-up of the positive contact point at the input end and the negative metal spring clip on the side. The metal contacts have a smooth surface and provide good elastic support.
Product Dimensions and Weight
Measured with calipers, the length of the car charger body is 101.52mm.
Measured width is 52.57mm.
Measured thickness is 36.16mm.
Measured with an electronic scale, the net weight of the car charger is approximately 71.9g.
The intuitive size comparison when held in hand is shown in the image.
Fast Charging Protocol Testing
First, set the input voltage to 24.000V using the POWER-Z P240 to simulate the 24V cigarette lighter power supply environment of diesel vehicles for protocol detection.
Upon powering on, the digital display screen on the top of the car charger lights up, showing the circular total power interface.
Switching to the independent monitoring interface for the three ports distinguishes USB-C2, USB-A, and USB-C1 with different background colors, displaying real-time output power, voltage, and current for each port.
Testing with the POWER-Z KM003C reveals that the USB-C1 port supports VFCP, QC3.0, QC5, FCP, SCP, AFC, PD3.0/PPS, DCP, and other charging protocols.
PDO messages indicate that the USB-C1 port supports PD3.0 100W fast charging, featuring five fixed voltage profiles: 5V3A, 9V 3A, 12V 3A, 15V 3A, and 20V 5A, along with two PPS voltage ranges: 3.6-11V 6A and 3.6-20V 6A. It also supports Xiaomi's 120W Surge Instant Charge.
Testing shows the USB-C1 port supports maximum 200.0W VFCP fast charging, with two output specifications: 11.00V 6.00A and 20.00V 10.00A.
Testing reveals that the USB-C2 port supports QC3+, QC4+, FCP, SCP, AFC, PD3.0/PPS, DCP, Apple 2.4A, and other charging protocols.
Testing shows the USB-C2 port features five fixed voltage profiles: 5V 3A, 9V 3A, 12V 3A, 15V 3A, and 20V 2.25A, along with one PPS voltage range: 3.3-11V 5A.
Testing reveals that the USB-A port supports VFCP, QC3+, FCP, SCP, AFC, TFCP, and DCP charging protocols.
Next, adjust the POWER-Z P240 output voltage to 14.000V to simulate standard gasoline vehicle battery voltage.
At 14V input, USB-C1 compatibility remains the same.
USB-C2 compatibility also remains the same.
USB-A compatibility also remains the same.
Having briefly reviewed the product appearance and fast charging compatibility, we now proceed to the teardown section.
Product Teardown
Pry open the housing along the seam of the output top cover and extract the internal PCBA module.
The screen module inside the top cover is connected to the PCBA via an FPC ribbon cable.
Overview of the inner structure of the output top cover. Clips are arranged around the perimeter for fixation. Three openings corresponding to the USB female connectors are reserved at the top, and a color LCD display is secured at the bottom.
The PCBA module adopts a T-shaped structure overall. The front end is a long strip-shaped small board for positive and negative power extraction, while the rear end is the main control PCB. The front end of the power extraction board is soldered with the positive spring contact and negative metal spring clip.
The front side of the board distributes components such as input filter capacitors, SMD fuses, three toroidal inductors, output filter capacitors, and three USB output female connectors.
The back side concentrates components such as buck-boost chips, step-down chips, protocol chips, MCUs, and MOSFETs.
The Powlicon PL5501 is a synchronous four-switch unidirectional buck-boost controller, packaged in QFN32.
This chip operates stably within a wide input voltage range of 3.6V to 32V (maximum 36V) with a continuous load current capability of 20A. It can regulate the output voltage stably whether the input is higher or lower than the output, supporting various buck-boost applications and providing an optimal solution for high-power Type-C PD car chargers.
Four buck-boost switching transistors come from CQAOS Chongqing Wanguo, marked with "6534N".
Two filter inductors, insulated with external heat shrink tubing.
One buck-boost inductor, also insulated with heat shrink tubing.
Two ST Shengtong input filter capacitors, rated at 35V 100μF.
The NDPSEMI Xintanwei NDP23301KC is a synchronous step-down chip with a wide input voltage range of 4.6V~30V, packaged in SOP8.
Its maximum output current is 3A, supporting adjustable output voltage with ±2% output voltage accuracy. The chip features built-in power MOSFETs, burst mode operation under light loads, and internal soft-start functionality.
One protocol chip corresponding to USB-C1, marked with "SM002H".
One VBUS transistor from AGMsemi Xinkongyuan, model AGM406AP, with a breakdown voltage of 40V and on-resistance of 6.5mΩ, packaged in PDFN3333.
One step-down protocol chip corresponding to USB-C2 comes from FM Fuman Micro, model XPM5220, packaged in ESOP8.
The chip integrates a synchronous step-down converter and power MOSFETs, supporting fast charging protocols such as USB PD, QC2.0/3.0/3.0+, FCP/SCP/HVSCP, VOOC 2.0/4.0, PE, and AFC.
One unmarked protocol chip corresponding to USB-A.
Three ST Shengtong output filter capacitors, rated at 25V 220μF.
One LDO regulator chip, marked with "7533-1".
One unmarked MCU, used to drive the display screen.
Teardown complete. Here is a group photo of all components.
Charging Head Network Summary
Finally, attached is the bill of materials for the product for your reference.
Newsmy's 200W car charger features three output ports (2C1A). In terms of performance, it supports PD3.0/PPS, QC, SCP, and Xiaomi Surge Instant Charge VFCP, among others.
The top panel integrates a color smart digital display screen that shows total output power and individual port power, voltage, and current parameters in real-time, meeting the car fast-charging needs of laptops and smartphones from multiple brands.
Through the teardown, Charging Head Network learned that the internal PCBA module uses a T-shaped structure, with the screen module connected to the main board via an FPC ribbon cable. The internal buck-boost circuit employs the Powlicon PL5501 synchronous buck-boost controller, paired with four CQAOS Chongqing Wanguo switching transistors. One step-down chip is the NDPSEMI Xintanwei NDP23301KC.
USB-C1 utilizes the SM002H protocol chip and the AGM406AP VBUS transistor from Xinkongyuan. The Fuman Micro XPM5220 step-down protocol chip corresponds to the USB-C2 port, while an unmarked protocol chip corresponds to the USB-A port.
Additionally, there is an unmarked MCU used to drive the digital display screen. Both input and output filtering use electrolytic capacitors from Shengtong.