EN / 中文

UGREEN 67W Travel Fast Charger with Smart Display Teardown: Global Multi-Plug 2C1A Charger

by chongdiantouwang·November 19, 2026

Recently, UGREEN launched its new generation 67W travel fast charger with an intelligent display. This device integrates multi-region global conversion plugs, a 67W three-port fast charging system, and a visualized smart display into a single unit, pioneering a new form factor for travel charging.

This charger supports 100-240V global wide-voltage input. The body features push-pull and folding US, AU, UK, and EU plugs, allowing users to travel seamlessly across multiple countries or regions with just one charger.

Leveraging vertical stacking technology, the body size is controlled to be comparable to a pack of portable tissues. It also adopts a low-center-of-gravity mechanical design, ensuring it stays firmly plugged into wall outlets without easily falling out.

In terms of interfaces, it is equipped with two USB-C ports and one USB-A port (2C1A). Both USB-C1 and C2 support up to 67W PD fast charging output on a single port, while the USB-A port supports 22.5W fast charging. Simultaneous charging via all three ports is supported.

The front of the body features a smart display screen and touch buttons. Users can view real-time charging power, voltage, current, handshake protocols, and intelligent temperature control status. It also supports manually enabling PPS priority and always-on display modes, catering to the fast charging needs of major smartphone brands, tablets, and thin-and-light laptops.

It is understood that the interior of this charger utilizes a complete fast charging power solution from iSmartWare, featuring the SW1192H primary controller chip, SW1608 synchronous rectification controller, and SW3578 buck protocol chip, achieving a full-link design.

Recently, this product was selected as part of the APEC meeting week supply bag.

Product Appearance

The packaging box features a steady black color scheme. The brand logo and four core selling points are printed in the top left corner, with a rendering of the product appearance in the center.

The side of the packaging box lists the four plug standards supported by the product: US, AU, UK, and EU.

The back of the packaging box displays the product parameter nameplate, which will be introduced in detail during the physical inspection section.

Upon opening the package, the contents include the UGREEN 67W travel fast charger itself and a card detailing after-sales service policies.

The front of the charger is covered by a glossy pure black panel housing a hidden smart display screen. Below the UGREEN brand logo is the icon for the touch button.

The body features a square, flat columnar shape with rounded corners. Thanks to the low-center-of-gravity structural design, it sits closer to the wall when plugged in, maintaining balanced force distribution and resisting loosening or detachment.

The waist of the body is treated with a delicate deep space gray metallic paint finish. The text "67W" indicating power output is printed in black on the bottom right corner of the side.

The rear of the body integrates a multi-in-one plug module. In the retracted state, all plugs are hidden inside the body, facilitating travel storage and preventing scratches on other items in the bag.

The US plug at the top can be rotated to convert into an AU plug once extended.

Pressing the circular push button on top and moving it forward ejects the US plug at the front end. Once fully extended, the internal latch automatically locks, ensuring the plug remains stable and does not retract during insertion or removal.

Rotating inward according to the arrow indicators on the body switches the configuration to the AU plug.

Flipping up the central plastic grounding pin converts the configuration to a UK three-pin plug.

Foldable EU plugs are located at the bottom.

The bottom output end of the body features two USB-C ports and one USB-A port (2C1A). The USB-A port has a purple insert, while the two USB-C ports have black inserts.

The nameplate parameters on the side of the charger are as follows:

Product Name: 67W Travel Fast Charger

Model: X576

Input: 100-240V~ 50/60Hz 1.8A Max

USB-C1/C2 Output: 5.0V3.0A/9.0V3.0A/15.0V3.0A/20.0V3.35A 67.0W Max

USB-A Output: 5.0V3.0A/9.0V2.0A/12.0V1.5A/10.0V2.25A 22.5W Max

Total Output Power: 67.0W Max

Manufacturer: Shenzhen UGREEN Technology Co., Ltd.

The product has passed safety certifications such as FCC, CE, and UKCA.

Product Dimensions and Weight

Measured with calipers, the length of the charger body is 88.56mm.

The measured thickness of the charger body is 31.28mm.

The measured width of the charger body is 52.25mm.

The intuitive feel of holding the charger in hand is shown in the figure.

A comparison between the UGREEN 67W travel fast charger with display and the Apple 67W charger is shown in the figure.

Weighing on a digital scale, the net weight of the charger is approximately 164.4g.

Product Smart Display Interaction

When the charger is connected to power but no device is attached, the front display lights up, showing a standby state of 0W centered on the dial.

Tapping the touch button below the panel provides real-time feedback on the operating status of the intelligent temperature control system through blue dynamic graphics.

Continuing to short-press the touch key switches to the settings entry page, where the screen prompts to long-press for 2 seconds to enter settings.

After entering the settings menu via long press, a switch for the PPS priority function is provided. Long-pressing for 2 seconds toggles it on/off. When enabled, it prioritizes guiding devices to handshake high-power PPS fast charging.

In the settings menu, short-pressing switches to the always-on display option, which also supports toggling on/off via a 2-second long press.

Fast charging tests were conducted using the USB-C1 port to charge an iPhone 18 Pro Max.

After connecting the iPhone 18 Pro Max, the screen displays the real-time output power of the C1 port and the cable specifications.

Tapping the button again switches the interface, intuitively displaying the current real-time voltage, real-time current, and the active PD fast charging protocol for the C1 port, allowing full control over charging details on one screen.

Switching to the main dial interface displays the current total output power of 45W.

Product Fast Charging Protocol Testing

The product supports toggling PPS priority mode on/off, switching between PD3.0/PPS mode and PD3.2/AVS mode. First, PPS priority mode was enabled for testing.

Using the POWER-Z KM003C, it was determined that the USB-C1 port supports QC3.0, AFC, PD3.0/PPS, QC5, DCP, and Apple 2.4A charging protocols.

The PDO message shows that the USB-C1 port has four fixed voltage levels: 5V3A, 9V3A, 15V3A, and 20V3.35A, along with two PPS voltage ranges: 5.00-11.00V 5.00A and 5.00-21.00V 3.00A.

The USB-C2 port was found to support QC3+, AFC, PD3.0/PPS, QC5, DCP, and Apple 2.4A charging protocols.

The PDO is identical to that of USB-C1.

The USB-A port was found to support QC3+, AFC, DCP, and Apple 2.4A charging protocols.

Next, PPS priority mode was disabled for testing.

The USB-C1 port was found to support QC3.0, AFC, PD3.2/AVS, DCP, and Apple 2.4A charging protocols.

The PDO message shows that the USB-C1 port has four fixed voltage levels: 5V3A, 9V3A, 15V3A, and 20V3.35A, along with two AVS voltage ranges: 9-20V 3A/3.35A.

The USB-C2 port was found to support QC3+, FCP, SCP, AFC, PD3.2/AVS, DCP, and Apple 2.4A charging protocols.

The PDO message shows that the USB-C2 port has four fixed voltage levels: 5V3A, 9V3A, 15V3A, and 20V3.35A, along with two AVS voltage ranges: 9-20V 3A/3.35A.

The USB-A port was found to support QC3+, FCP, SCP, AFC, DCP, and Apple 2.4A charging protocols.

With PPS priority disabled, actual testing with an iPhone 18 Pro Max showed a voltage of 17.56V, current of 2.96A, and power of 52.12W, successfully activating PD3.2 AVS fast charging.

Product PCBA Overview Analysis

Removing the transparent decorative cover on the front and the interface panel reveals a black plastic positioning middle frame inside, secured by screws at the four corners and clips.

An overview of the inner side of the front cover shows a light-transmitting window for the display at the top. The touch button area at the bottom features conductive copper foil for transmitting touch signals.

The four corners of the black plastic middle frame are fixed with Phillips screws. Metal touch springs protrude from the bottom.

After removing the plastic middle frame, the display module is fixed to its back and connected to the PCBA module via an FPC ribbon cable.

The PCBA module is removed from the shell.

A close-up of the multi-country plug mechanical structure at the bottom of the shell.

An overview of the front of the PCBA module shows a multi-board vertical stacking architecture with compact component placement. Adequate white glue is applied around high-voltage capacitors, inductors, and the transformer for fixation.

The back of the PCBA module features thermal paste to accelerate heat dissipation.

The measured length of the PCBA module is approximately 69.06mm.

The measured width of the PCBA module is approximately 46.67mm.

The measured thickness of the PCBA module is approximately 19.14mm.

After cleaning off the white glue from the PCBA module, the front view shows the buck small board for output at the top, the transformer in the middle, the screen driver small board on the left, and four high-voltage filter electrolytic capacitors, the rectifier bridge small board, and the input EMI small board densely arranged on the right and bottom.

The back of the PCBA module is shown in the figure.

The output end is shown in the figure.

The input end is shown in the figure.

The multiple small boards on the PCBA module are separated sequentially.

An overview of the front of the input EMI filtering small board shows components soldered from left to right: delay fuse, NTC thermistor, safety X2 capacitor, and common-mode inductor.

The back of the input EMI filtering small board has no components.

The front of the rectifier small board features a SMD rectifier bridge.

The back of the rectifier small board features high-voltage filter capacitors.

The front of the bottom mainboard features the transformer, output filter solid capacitors, three high-voltage filter electrolytic capacitors, main controller power supply capacitors, and differential mode inductors.

An overview of the back of the bottom mainboard shows clear separation between primary and secondary sides, featuring components such as the primary controller chip, synchronous rectification chip, primary switching tube, synchronous rectification tube, optocoupler, and SMD Y-capacitors.

The front of the screen display driver small board features an MCU screen driver chip, memory chip, and connector for the screen.

An overview of the back of the screen driver small board shows components such as a crystal oscillator, buck inductor, and buck IC.

The front of the output buck small board features three female connectors (2C1A), filter capacitors, buck inductors, and VBUS tubes.

The back of the output buck small board features the buck protocol chip and VBUS tubes.

Observation of the PCBA module reveals that this UGREEN67W travel fast charger uses a QR flyback switching power supply design.

The primary side drives a SiC MOSFET, the secondary side outputs fixed voltage via synchronous rectification, and two synchronous buck circuits achieve2C1A three-port fast charging output. We will now examine the specific information of each component starting from the input end.

Product Primary Side Analysis

A close-up of the input delay fuse, used for overcurrent protection at the input end.

A close-up of the NTC thermistor, used to suppress surge currents.

The safety X2 capacitor is from KNSCMA (Kenisheng), with a specification of 0.1μF, used to filter differential mode interference from the power grid.

The common-mode inductor adopts a bidirectional parallel winding design, insulated externally with black heat shrink tubing, used to filter EMI common-mode interference.

The rectifier bridge is from PY (Pingwei), model TBMR810, rated 8A 1000V, using TBM packaging.

A drum core inductor is wrapped externally with black heat shrink tubing for insulation.

One high-voltage filter capacitor is from Koshin (Dongjia), rated 400V 33μF.

Another high-voltage filter capacitor is from Koshin (Dongjia), rated 400V 33μF.

Two high-voltage filter electrolytic capacitors are from Koshin (Dongjia), each rated 400V 15μF.

The power supply capacitor for the primary controller chip is also from Koshin (Dongjia).

The built-in primary controller chip is from iSmartWare, model SW1192H, using SOT23-6 packaging.

This chip is a high-frequency quasi-resonant current-mode PWM controller designed specifically for offline flyback power supplies and chargers. It features a built-in DRV drive stage capable of directly driving SiC MOSFETs, with maximum pull-up/pull-down output current capabilities of approximately 100mA / 500mA respectively, simplifying external drive circuit design and supporting transient power requirements.

The chip also supports ultra-wide VDD supply voltage ranging from 12–90V and includes built-in quasi-resonant optimization strategies such as soft start, frequency dithering, and valley turn-on/valley locking. These features effectively reduce switching losses and improve EMI performance, maintaining high efficiency and good electromagnetic compatibility even at high frequencies.

The primary switching tube is from NEXIC Technology, a SiC MOSFET model NKD280P080D21, rated 800V with 280mΩ Rds(on), using PDFN5*6 packaging.

A close-up of an optocoupler marked OR1008, used for signal isolation communication between primary and secondary sides and output voltage feedback regulation.

Two SMD Y-capacitors bridge the primary and secondary sides, from JINGQIN, part number 1Y1X1Y5P471K.

The transformer surface is marked ATQ25-T0267R067 XDWY 2638.

Synchronous Rectification Circuit Analysis

The synchronous rectification chip is also from iSmartWare, model SW1608. This is a high-performance controller for secondary-side synchronous rectification tube drivers in offline flyback converters, using SOT23-6 packaging.

It supports 6V or 9V VCC supply, with self-powered VCC functionality eliminating the need for auxiliary winding supply and supporting a wide output voltage range. Used with MOSFETs to replace Schottky rectifier diodes, it significantly improves system efficiency.

SW1608 supports a 600KHz operating frequency and various application scenarios including High Side/Low Side, supporting CCM/QR/DCM operating modes.

Additionally, it integrates intelligent turn-on detection to effectively prevent false turn-ons caused by DCM ringing; the chip also features ultra-low turn-off propagation delay time and strong pull-down current capability, significantly reducing voltage stress on the rectification tube.

The synchronous rectification tube is from AGMsemi (Xinkongyuan), model AGM1010A, rated 100V with 7.2mΩ Rds(on), using PDFN5*6 packaging.

Two output filter solid capacitors are from JSH (Wanjingyuan), each rated 25V 470μF.

Product Buck Fast Charging Output Circuit Analysis

The built-in SW3578 is a buck protocol chip launched by iSmartWare, using QFN36 packaging. It supports single-chip dual independent Type-C ports for fast charging and can be expanded to 2C1A output, achieving up to 28V/5A 140W output without requiring external buck controllers.

The chip internally integrates a 32-bit MCU and dual independent Type-C logic, supporting various fast charging protocols including PD3.2 SPR AVS, PD3.2 EPR AVS, UFCS, SCP, FCP, QC5/4+/4/3+/3.0/2.0, AFC, PE2.0/1.1, and TFCP, as well as custom private protocols.

SW3578 integrates a 10A high-efficiency switch buck converter, using external dual NMOS and supporting real-time bus voltage adjustment.

Simultaneously, the rated output current reaches 10A, with switch frequency configurable in four steps: 125/180/333/500 kHz. It supports automatic switching between light-load PFM and medium/heavy-load PWM, with a maximum duty cycle >99%.

SW3578 supports a wide input voltage range of 4.5-32V and three-channel NMOS drive control, allowing the chip to connect directly to vehicle power buses or pair with external power paths or secondary DC/DC stages for more complex power supply topologies.

The buck MOSFET is from AGMsemi (Xinkongyuan), model AGM304AP, rated 30V with 3.8mΩ Rds(on), using PDFN3.3*3.3 packaging.

A close-up of two synchronous buck inductors.

The VBUS tube corresponding to USB-C1 is also Xinkongyuan AGM304AP.

The VBUS tube corresponding to USB-C2 is also Xinkongyuan AGM304AP.

The VBUS tube corresponding to USB-A is also Xinkongyuan AGM304AP.

One output filter capacitor is from Dongjia, rated 25V 150μF.

Another output filter capacitor is also from Dongjia, rated 25V 150μF.

A third output filter capacitor is from JSH (Wanjingyuan), rated 25V 100μF.

Screen Driver Circuit Analysis

The MCU on the screen display driver small board is from Synwit (Huaxin Weite), model SWM221K8U7.

This is a microcontroller based on a 32-bit ARM Cortex-M0 core, using QFN32 packaging. It is responsible for receiving real-time data reported by the fast charging protocol chips regarding voltage, current, protocol data, and NTC temperature information for each port, and driving the front TFT smart color screen to render dynamic UI interfaces.

A crystal oscillator is soldered on the back of the screen driver small board, providing a high-precision clock signal for the Synwit MCU.

Next to the MCU is an external NOR Flash memory from PUYA (Puran), model PY25Q128HA, using SOP-8 packaging with 128Mbit storage capacity, used to store firmware information.

A chip marked 3FP958.

A buck chip marked T74Ag11.

A chip marked T3352C, with a touch spring nearby.

All disassembly completed, here is a group photo.

Chongdiantou Summary

Finally, the product bill of materials is attached for reference.

The UGREEN 67W travel fast charger with display integrates global multi-country conversion plugs with 67W 2C1A multi-port fast charging and supports 100-240V wide-voltage input, meeting travel needs across multiple regions globally.

Additionally, the product supports one-click activation of PPS priority mode via the body menu, satisfying the fast charging needs of diverse devices.

Through disassembly, Chongdiantou learned that this travel charger internally employs a multi-board stacking architecture to save space, and the plug module features mechanical interlocking and spring-loaded contact designs for safety and reliability.

The entire unit uses a complete fast charging power solution from iSmartWare. The primary side pairs the iSmartWare SW1192H primary controller chip with an NEXIC SiC switching tube, while the secondary side uses the iSmartWare SW1608 synchronous rectification controller paired with an AGMsemi synchronous rectification tube for output.

The output end achieves 2C1A three-port fast charging through the iSmartWare SW3578 buck protocol chip working in conjunction with two synchronous buck circuits.

The smart display is driven by the Synwit SWM221K8U7 MCU paired with PUYA NOR Flash to enable intelligent interaction functions.

Overall, the product demonstrates solid craftsmanship and component selection, stable output performance, making it highly suitable for consumers who require multi-country travel charging solutions.